SUNScholar - Browsing by Author "Gorgens, Johann F."

Browsing by Author "Gorgens, Johann F."

Now showing 1 - 9 of 9

Comparison of constitutive and inducible β-fructofuranosidase production by recombinant Pichia pastoris in fed-batch culture using defined and semi-defined media
(Elsevier, 2016) Anane, Emmanuel; Van Rensburg, Eugene; Gorgens, Johann F.
ENGLISH ABSTRACT: Short-chain fructooligosaccharides produced from sucrose by transfructosylation using β-fructofuranosidase (FFase), an industrially important enzyme, finds application in pre-biotics, sweeteners and confectionary products. Using recombinant Pichia pastoris, the influence of replacing the commonly-used Invitrogen® medium with a semi-defined medium for FFase production under the control of the glyceraldehyde-3-phosphate dehydrogenase (GAP) and alcohol oxidase (AOX) promoters was investigated. Replacing the trace metals (PTM1) solution with yeast extract resulted in a 54.3% decrease in FFase volumetric activity under control of the AOX promoter, suggesting a distinct requirement for trace metals for recombinant protein synthesis during methanol induction, given that the biomass yield on methanol decreased by only 10%. The same medium adjustment had no effect on enzyme production under GAP promoter control, although AOX promoter control resulted in double the FFase volumetric activity compared to glycerol-fed cultures. Decreasing basal salts by half did not affect the cultures, but alleviated precipitation during sterilisation. Optimisation of the glycerol feed rate and dissolved oxygen tension in DO-stat fed-batch fermentations using the semi-defined medium resulted in 17% increase in volutmetric activity of FFase expressed under the GAP promoter. This study highlighted the influence of carbon source and trace metals on heterologous protein production by P. pastoris using constitutive and inducible promoters.
Incorporating anaerobic co-digestion of steam exploded or ammonia fiber expansion pretreated sugarcane residues with manure into a sugarcanebased bioenergy-livestock nexus
(Elsevier, 2019) Mokomelea, Thapelo; Da Costa Sousa, Leonardo; Balan, Venkatesh; Van Rensburg, Eugene; Dale, Bruce E.; Gorgens, Johann F.
ENGLISH ABSTRACT: The co-digestion of pretreated sugarcane lignocelluloses with dairy cow manure (DCM) as a bioenergy production and waste management strategy, for intensive livestock farms located in sugarcane regions, was investigated. Ammonia fiber expansion (AFEX) increased the nitrogen content and accelerated the biodegradability of sugarcane bagasse (SCB) and cane leaf matter (CLM) through the cleavage of lignin carbohydrate crosslinks, resulting in the highest specific methane yields (292–299 L CH4/kg VSadded), biogas methane content (57–59% v/v) and biodegradation rates, with or without co-digestion with DCM. To obtain comparable methane yields, untreated and steam exploded (StEx) SCB and CLM had to be co-digested with DCM, at mass ratios providing initial C/N ratios in the range of 18 to 35. Co-digestion with DCM improved the nutrient content of the solid digestates, providing digestates that could be used as biofertilizer to replace CLM that is removed from sugarcane fields during green harvesting.
Multi-product biorefineries from lignocelluloses : a pathway to revitalisation of the sugar industry?
(BioMed Central, 2017-04-11) Farzad, Somayeh; Mandegari, Mohsen A.; Guo, Miao; Haigh, Kathleen F.; Shah, Nilay; Gorgens, Johann F.
Background Driven by a range of sustainability challenges, e.g. climate change, resource depletion and expanding populations, a circular bioeconomy is emerging and expected to evolve progressively in the coming decades. South Africa along with other BRICS countries (Brazil, Russia, India and China) represents the emerging bioeconomy and contributes significantly to global sugar market. In our research, South Africa is used as a case study to demonstrate the sustainable design for the future biorefineries annexed to existing sugar industry. Detailed techno-economic evaluation and Life Cycle Assessment (LCA) were applied to model alternative routes for converting sugarcane residues (bagasse and trash) to selected biofuel and/or biochemicals (ethanol, ethanol and lactic acid, ethanol and furfural, butanol, methanol and Fischer–Tropsch synthesis, with co-production of surplus electricity) in an energy self-sufficient biorefinery system. Results Economic assessment indicated that methanol synthesis with an internal rate of return (IRR) of 16.7% and ethanol–lactic acid co-production (20.5%) met the minimum investment criteria of 15%, while the latter had the lowest sensitivity to market price amongst all the scenarios. LCA results demonstrated that sugarcane cultivation was the most significant contributor to environmental impacts in all of the scenarios, other than the furfural production scenario in which a key step, a biphasic process with tetrahydrofuran solvent, had the most significant contribution. Conclusion Overall, the thermochemical routes presented environmental advantages over biochemical pathways on most of the impact categories, except for acidification and eutrophication. Of the investigated scenarios, furfural production delivered the inferior environmental performance, while methanol production performed best due to its low reagent consumption. The combined techno-economic and environmental assessments identified the performance-limiting steps in the 2G biorefinery design for sugarcane industry and highlighted the technology development opportunities under circular bioeconomy context.
Rational engineering of Saccharomyces cerevisiae towards improved tolerance to multiple inhibitors in lignocellulose fermentations
(BMC (part of Springer Nature), 2021-08-28) Brandt, Bianca A.; Garcia‑Aparicio, Maria D. P.; Gorgens, Johann F.; Van Zyl, Willem H.
Background: The fermentation of lignocellulose hydrolysates to ethanol requires robust xylose-capable Saccharomyces cerevisiae strains able to operate in the presence of microbial inhibitory stresses. This study aimed at developing industrial S. cerevisiae strains with enhanced tolerance towards pretreatment-derived microbial inhibitors, by identifying novel gene combinations that confer resistance to multiple inhibitors (thus cumulative inhibitor resistance phenotype) with minimum impact on the xylose fermentation ability. The strategy consisted of multiple sequential deltaintegrations of double-gene cassettes containing one gene conferring broad inhibitor tolerance (ARI1, PAD1 or TAL1) coupled with an inhibitor-specific gene (ADH6, FDH1 or ICT1). The performances of the transformants were compared with the parental strain in terms of biomass growth, ethanol yields and productivity, as well as detoxification capacities in a synthetic inhibitor cocktail, sugarcane bagasse hydrolysate as well as hardwood spent sulphite liquor. Results: The first and second round of delta-integrated transformants exhibited a trade-off between biomass and ethanol yield. Transformants showed increased inhibitor resistance phenotypes relative to parental controls specifically in fermentations with concentrated spent sulphite liquors at 40% and 80% v/v concentrations in 2% SC media. Unexpectedly, the xylose fermentation capacity of the transformants was reduced compared to the parental control, but certain combinations of genes had a minor impact (e.g. TAL1 + FDH1). The TAL1 + ICT1 combination negatively impacted on both biomass growth and ethanol yield, which could be linked to the ICT1 protein increasing transformant susceptibility to weak acids and temperature due to cell membrane changes. Conclusions: The integration of the selected genes was proven to increase tolerance to pretreatment inhibitors in synthetic or industrial hydrolysates, but they were limited to the fermentation of glucose. However, some gene combination sequences had a reduced impact on xylose conversion.
Simultaneously improving xylose fermentation and tolerance to lignocellulosic inhibitors through evolutionary engineering of recombinant Saccharomyces cerevisiae harbouring xylose isomerase
(BioMed Central, 2014-05) Smith, Justin; Van Rensburg, Eugene; Gorgens, Johann F.
Background: Yeasts tolerant to toxic inhibitors from steam-pretreated lignocellulose with xylose co-fermentation capability represent an appealing approach for 2nd generation ethanol production. Whereas rational engineering, mutagenesis and evolutionary engineering are established techniques for either improved xylose utilisation or enhancing yeast tolerance, this report focuses on the simultaneous enhancement of these attributes through mutagenesis and evolutionary engineering of Saccharomyces cerevisiae harbouring xylose isomerase in anoxic chemostat culture using non-detoxified pretreatment liquor from triticale straw. Results: Following ethyl methanesulfonate (EMS) mutagenesis, Saccharomyces cerevisiae strain D5A+ (ATCC 200062 strain platform), harbouring the xylose isomerase (XI) gene for pentose co-fermentation was grown in anoxic chemostat culture for 100 generations at a dilution rate of 0.10 h−1 in a medium consisting of 60% (v/v) non-detoxified hydrolysate liquor from steam-pretreated triticale straw, supplemented with 20 g/L xylose as carbon source. In semi-aerobic batch cultures in the same medium, the isolated strain D5A+H exhibited a slightly lower maximum specific growth rate (μmax = 0.12 ± 0.01 h−1) than strain TMB3400, with no ethanol production observed by the latter strain. Strain D5A+H also exhibited a shorter lag phase (4 h vs. 30 h) and complete removal of HMF, furfural and acetic acid from the fermentation broth within 24 h, reaching an ethanol concentration of 1.54 g/L at a yield (Yp/s) of 0.06 g/g xylose and a specific productivity of 2.08 g/gh. Evolutionary engineering profoundly affected the yeast metabolism, given that parental strain D5A+ exhibited an oxidative metabolism on xylose prior to strain development. Conclusions: Physiological adaptations confirm improvements in the resistance to and conversion of inhibitors from pretreatment liquor with simultaneous enhancement of xylose to ethanol fermentation. These data support the sequential application of random mutagenesis followed by continuous culture under simultaneous selective pressure from inhibitors and xylose as primary carbon source.
Techno-economic comparison of ethanol and electricity coproduction schemes from sugarcane residues at existing sugar mills in Southern Africa
(BioMed Central, 2014-07) Petersen, Abdul M.; Aneke, Mathew C.; Gorgens, Johann F.
Background: The economics of producing only electricity from residues, which comprise of surplus bagasse and 50% post-harvest residues, at an existing sugar mill in South Africa was compared to the coproduction of ethanol from the hemicelluloses and electricity from the remaining solid fractions. Six different energy schemes were evaluated. They include: (1) exclusive electricity generation by combustion with high pressure steam cycles (CHPSC-EE), (2) biomass integrated gasification with combined cycles (BIGCC-EE), (3) coproduction of ethanol (using conventional distillation (CD)) and electricity (using BIGCC), (4) coproduction of ethanol (using CD) and electricity (using CHPSC), (5) coproduction of ethanol (using vacuum distillation (VD)) and electricity (using BIGCC), and (6) coproduction of ethanol (using VD) and electricity (using CHPSC). The pricing strategies in the economic analysis considered an upper and lower premium for electricity, on the standard price of the South African Energy Provider Eskom’ of 31 and 103% respectively and ethanol prices were projected from two sets of historical prices. Results: From an energy balance perspective, ethanol coproduction with electricity was superior to electricity production alone. The VD/BIGCC combination had the highest process energy efficiency of 32.91% while the CHPSC-EE has the lowest energy efficiency of 15.44%. Regarding the economic comparison, it was seen that at the most conservative and optimistic pricing strategies, the ethanol production using VD/BIGCC had the highest internal rate of returns at 29.42 and 40.74% respectively. Conclusions: It was shown that bioethanol coproduction from the hemicellulose fractions of sugarcane residues, with electricity cogeneration from cellulose and lignin, is more efficient and economically viable than the exclusive electricity generation technologies considered, under the constraints in a South African context.
Techno-economics of integrating bioethanol production from spent sulfite liquor for reduction of greenhouse gas emissions from sulfite pulping mills
(BioMed Central, 2014-12) Petersen, Abdul M.; Haigh, Kate; Gorgens, Johann F.
Background Flow sheet options for integrating ethanol production from spent sulfite liquor (SSL) into the acid-based sulfite pulping process at the Sappi Saiccor mill (Umkomaas, South Africa) were investigated, including options for generation of thermal and electrical energy from onsite bio-wastes, such as bark. Processes were simulated with Aspen Plus® for mass- and energy-balances, followed by an estimation of the economic viability and environmental impacts. Various concentration levels of the total dissolved solids in magnesium oxide-based SSL, which currently fuels a recovery boiler, prior to fermentation was considered, together with return of the fermentation residues (distillation bottoms) to the recovery boiler after ethanol separation. The generation of renewable thermal and electrical energy from onsite bio-wastes were also included in the energy balance of the combined pulping-ethanol process, in order to partially replace coal consumption. The bio-energy supplementations included the combustion of bark for heat and electricity generation and the bio-digestion of the calcium oxide SSL to produce methane as additional energy source. Results Ethanol production from SSL at the highest substrate concentration was the most economically feasible when coal was used for process energy. However this solution did not provide any savings in greenhouse gas (GHG) emissions for the concentration-fermentation-distillation process. Maximizing the use of renewable energy sources to partially replace coal consumption yielded a satisfactory economic performance, with a minimum ethanol selling price of 0.83 US$/l , and a drastic reduction in the overall greenhouse gas emissions for the entire facility. Conclusion High substrate concentrations and conventional distillation should be used when considering integrating ethanol production at sulfite pulping mills. Bio-wastes generated onsite should be utilized at their maximum potential for energy generation in order to maximize the GHG emissions reduction.
Thermogravimetric study of the pyrolysis characteristics and kinetics of coal blends with corn and sugarcane residues
(Elsevier, 2013) Aboyade, Akinwale O.; Gorgens, Johann F.; Carrier, Marion; Meyer, Edson L.; Knoetze, Johannes H.
This paper investigates the non-isothermal thermokinetics of the co-pyrolysis of sugarcane bagasse and corn residue blended with coal. The individual devolatilization behaviour of each of the fuels obtained separately was compared with the behaviour of the biomass blends with coal at various mix ratios. Possible synergistic behaviour that points to the existence of chemical interactions during pyrolysis between the coal and biomass fractions of the blends could thus be quantified. Synergistic interactions in the blends resulted in higher than expected volatile yields. The interactions occurred between 300 °C and 500 °C, corresponding to the end of biomass devolatilization and the start of coal decomposition. Isoconversional kinetic analysis revealed that apparent activation energy values varied between 165–180, 162–190, 160–175, and 225–260 kJ mol− 1 for sugarcane bagasse, corn cobs, corn stover, and coal in the 0.1 to 0.8 conversion range. A comparison of E(α) for single fuels and coal-biomass blends gave further evidence of synergistic behaviour as demonstrated by larger variation in E(α) during the decomposition of the blends, compared to the individual fuels.
Why pursue research projects in an academic environment
(Stellenbosch : Stellenbosch University, 2013-09) Gorgens, Johann F.
The pursuit of academic research is internationally considered to be a key deliverable of academic careers, with ever-increasing expectations of demonstrated research capacity and outputs as a means to substantiate academic excellence. The motivation behind granting such priority to research in the academic environment warrants careful consideration, considering the amount of time, effort and funding invested in these activities. Such consideration is the goal of the present essay, with particular application to the engineering and scientific domains of academic research.

Browsing by Author "Gorgens, Johann F."

Results Per Page

Sort Options